Anionic polyacrylamide Flopam AN920 SH can be replaced by Chinafloc A0310

 

Anionic polyacrylamide Flopam AN920 SH is a kind of anionic polyacrylamide with none hydrolysis degree and 8-10million molecular weight mainly used for mineral processing.Chinafloc A0310 can replace of it totally with good performance 

The quantity of mineral processing wastewater is large, there are more suspended substances and more types of toxic substances. The harmful substances in beneficiation wastewater are heavy metal ions and beneficiation agents. Heavy metal ions include copper, zinc, lead, nickel, barium, cadmium, arsenic and rare elements.

Concentrator special polyacrylamide series products are high degree of synthesis of water soluble linear polymer. Completely soluble in water, due to its microscopic form, can dissolve quickly. Different types of polypropylene have different active groups, can condense different suspended particles, easy filtration and separation. This series of products is almost insoluble in any organic solvent, but rather heavily soluble in water. It is widely used in many industries in the fields of flocculation, viscosity, bonding, scale inhibition, stable colloid, drag reduction, film formation, gel, biological materials and so on. The product has high viscosity and can effectively treat sewage from concentrator.

 

Polyacrylamide selection:

 

The general choice of anionic polyacrylamide (generally weak anionic polyacrylamide and medium anionic polyacrylamide), molecular weight requirements in more than 15 million. Sometimes non-ionic polypropylene such as strongly acidic water is used. Note: Different manufacturers, the same parameters of the product, the use effect is often very different. In short, the key is to choose the most cost-effective manufacturer of coagulant, strict operation in use, cost control.

 

Notes on the use of polyacrylamide:

 

1. Experiment: Choose which kind of polyacrylamide from which factory, to decide by experiment. Select the right manufacturer, the right ionic type, molecular weight, ionic degree, degree of hydrolysis, etc.

 

2. dissolution concentration: general polyacrylamide dissolution concentration of 0.2% ~ 0.5%, the specific use of concentration depends on the material characteristics and use conditions, through the experiment to determine. The majority is 0.2-0.3 percent.

 

3. Good dissolution is key. The dissolving water must be tap water or clean water, and the dissolving temperature must be lower than 60. The dissolving time is usually more than 45 minutes, but not more than 60 minutes. The linear speed of dissolution agitation is generally 6 ~ 8m/s.

 

4. The proportion of added dosage should be determined by experiment. The specific dosage ratio depends on the concentration of the material to be treated, material characteristics, through the experiment to determine the dosage ratio, dosage is too high, may backfire. Controlling the appropriate dose rate is the key to controlling the cost.

The quantity of mineral processing wastewater is large, there are more suspended substances and more types of toxic substances. The harmful substances in beneficiation wastewater are heavy metal ions and beneficiation agents. Heavy metal ions include copper, zinc, lead, nickel, barium, cadmium, arsenic and rare elements.

Concentrator special polyacrylamide series products are high degree of synthesis of water soluble linear polymer. Completely soluble in water, due to its microscopic form, can dissolve quickly. Different types of polypropylene have different active groups, can condense different suspended particles, easy filtration and separation. This series of products is almost insoluble in any organic solvent, but rather heavily soluble in water. It is widely used in many industries in the fields of flocculation, viscosity, bonding, scale inhibition, stable colloid, drag reduction, film formation, gel, biological materials and so on. The product has high viscosity and can effectively treat sewage from concentrator.

 

Polyacrylamide selection:

 

The general choice of anionic polyacrylamide (generally weak anionic polyacrylamide and medium anionic polyacrylamide), molecular weight requirements in more than 15 million. Sometimes non-ionic polypropylene such as strongly acidic water is used. Note: Different manufacturers, the same parameters of the product, the use effect is often very different. In short, the key is to choose the most cost-effective manufacturer of coagulant, strict operation in use, cost control.

 

Notes on the use of polyacrylamide:

 

1. Experiment: Choose which kind of polyacrylamide from which factory, to decide by experiment. Select the right manufacturer, the right ionic type, molecular weight, ionic degree, degree of hydrolysis, etc.

 

2. dissolution concentration: general polyacrylamide dissolution concentration of 0.2% ~ 0.5%, the specific use of concentration depends on the material characteristics and use conditions, through the experiment to determine. The majority is 0.2-0.3 percent.

 

3. Good dissolution is key. The dissolving water must be tap water or clean water, and the dissolving temperature must be lower than 60. The dissolving time is usually more than 45 minutes, but not more than 60 minutes. The linear speed of dissolution agitation is generally 6 ~ 8m/s.

 

4. The proportion of added dosage should be determined by experiment. The specific dosage ratio depends on the concentration of the material to be treated, material characteristics, through the experiment to determine the dosage ratio, dosage is too high, may backfire. Controlling the appropriate dose rate is the key to controlling the cost.

The quantity of mineral processing wastewater is large, there are more suspended substances and more types of toxic substances. The harmful substances in beneficiation wastewater are heavy metal ions and beneficiation agents. Heavy metal ions include copper, zinc, lead, nickel, barium, cadmium, arsenic and rare elements.

Concentrator special polyacrylamide series products are high degree of synthesis of water soluble linear polymer. Completely soluble in water, due to its microscopic form, can dissolve quickly. Different types of polypropylene have different active groups, can condense different suspended particles, easy filtration and separation. This series of products is almost insoluble in any organic solvent, but rather heavily soluble in water. It is widely used in many industries in the fields of flocculation, viscosity, bonding, scale inhibition, stable colloid, drag reduction, film formation, gel, biological materials and so on. The product has high viscosity and can effectively treat sewage from concentrator.

 

Polyacrylamide selection:

 

The general choice of anionic polyacrylamide (generally weak anionic polyacrylamide and medium anionic polyacrylamide), molecular weight requirements in more than 15 million. Sometimes non-ionic polypropylene such as strongly acidic water is used. Note: Different manufacturers, the same parameters of the product, the use effect is often very different. In short, the key is to choose the most cost-effective manufacturer of coagulant, strict operation in use, cost control.

 

Notes on the use of polyacrylamide:

 

1. Experiment: Choose which kind of polyacrylamide from which factory, to decide by experiment. Select the right manufacturer, the right ionic type, molecular weight, ionic degree, degree of hydrolysis, etc.

 

2. dissolution concentration: general polyacrylamide dissolution concentration of 0.2% ~ 0.5%, the specific use of concentration depends on the material characteristics and use conditions, through the experiment to determine. The majority is 0.2-0.3 percent.

 

3. Good dissolution is key. The dissolving water must be tap water or clean water, and the dissolving temperature must be lower than 60. The dissolving time is usually more than 45 minutes, but not more than 60 minutes. The linear speed of dissolution agitation is generally 6 ~ 8m/s.

 

4. The proportion of added dosage should be determined by experiment. The specific dosage ratio depends on the concentration of the material to be treated, material characteristics, through the experiment to determine the dosage ratio, dosage is too high, may backfire. Controlling the appropriate dose rate is the key to controlling the cost.

The quantity of mineral processing wastewater is large, there are more suspended substances and more types of toxic substances. The harmful substances in beneficiation wastewater are heavy metal ions and beneficiation agents. Heavy metal ions include copper, zinc, lead, nickel, barium, cadmium, arsenic and rare elements.

Concentrator special polyacrylamide series products are high degree of synthesis of water soluble linear polymer. Completely soluble in water, due to its microscopic form, can dissolve quickly. Different types of polypropylene have different active groups, can condense different suspended particles, easy filtration and separation. This series of products is almost insoluble in any organic solvent, but rather heavily soluble in water. It is widely used in many industries in the fields of flocculation, viscosity, bonding, scale inhibition, stable colloid, drag reduction, film formation, gel, biological materials and so on. The product has high viscosity and can effectively treat sewage from concentrator.

 

Polyacrylamide selection:

 

The general choice of anionic polyacrylamide (generally weak anionic polyacrylamide and medium anionic polyacrylamide), molecular weight requirements in more than 15 million. Sometimes non-ionic polypropylene such as strongly acidic water is used. Note: Different manufacturers, the same parameters of the product, the use effect is often very different. In short, the key is to choose the most cost-effective manufacturer of coagulant, strict operation in use, cost control.

 

Notes on the use of polyacrylamide:

 

1. Experiment: Choose which kind of polyacrylamide from which factory, to decide by experiment. Select the right manufacturer, the right ionic type, molecular weight, ionic degree, degree of hydrolysis, etc.

 

2. dissolution concentration: general polyacrylamide dissolution concentration of 0.2% ~ 0.5%, the specific use of concentration depends on the material characteristics and use conditions, through the experiment to determine. The majority is 0.2-0.3 percent.

 

3. Good dissolution is key. The dissolving water must be tap water or clean water, and the dissolving temperature must be lower than 60. The dissolving time is usually more than 45 minutes, but not more than 60 minutes. The linear speed of dissolution agitation is generally 6 ~ 8m/s.

 

4. The proportion of added dosage should be determined by experiment. The specific dosage ratio depends on the concentration of the material to be treated, material characteristics, through the experiment to determine the dosage ratio, dosage is too high, may backfire. Controlling the appropriate dose rate is the key to controlling the cost.